Features of generator for high frequency induction welding machine
1. Magnetic induction heating, no flame, no waste gas.
2. IGBT technology, save electricity.
3. Work stable, performance well, 24 hours work continuoulsy.
4. Induction coils are easy to changed.
5. Can heat small different shaped metal work pieces.
6. Water cooled induction heater.
7. Easy to install and operate.
8. Simple maintenance,low cost.
Model | WH-VI-16 |
Work power | single phase 220V/50-60JHZ |
Working voltage(AC) | 180V-250V |
Max. output power | 16 KW ( power can be adjusted3-16KW) |
Oscillation frequency | 10-80 KHZ |
Max. output current | 42A |
Efficiency | 90% |
Continuous load rate | 100% |
Cooling water flow | 5L/min(0.1mpa) |
Copling water pressure | 0.1mpa |
Size Length*width*height | 500*240*450mm |
Net weight | 25kgs |
Water temperature protection | less than 50 degree |
Packing Size | 610*620*340mm , 0.13CBM |
Gross weight | 35kgs |
Packages | one wooden case (plywood) |
Transport method | by air ,by DHL or by sea |
Usage of generator WH-VI-16KW High frequency induction heating:
1. Metal wire annealing,hardening
2. Small rods heated, below Ø 10mm
3. Small pieces inductin brazing welding,such as diamond saw blades, carbide tips,gun drill etc.
Features of generator for igh frequency induction heating:
1. Magnetic induction heating, no flame, no waste gas.
2. IGBT technology, save electricity.
3. Work stable, performance well, 24 hours work continuoulsy.
4. Induction coils are easy to changed.
5. Can heat small different shaped metal work pieces.
6. Water cooled induction heater.
7. Easy to install and operate.
8. Simple maintenance,low cost.
Safety Panel:
Certificates
Applications
My contact information
manufacturer of welding machine and welding wire
high frequency induction welding machine
ZX7-250 IGBT Inverter welding machine
` The inverter technology will ensure welding current highly stable at grid voltage fluctuation and arc length changing. Arc is soft and can adjust automatically.
` Small welding splashing
` Welding deposition rate is high
` Little welding deformation and good weld shaping.
` Light in weight, small in size and portable.
` A high efficiency and energy saving equipment with high power factor.
- |
ZX7-200 |
ZX7-250 |
ZX7-315 |
ZX7-400A |
ZX7-400 |
ZX7-500 |
Input Power Voltage(V) |
AC220V±15% |
Three phase AC380V±15% |
||||
Frequency (HZ) |
50/60 |
50/60 |
50/60 |
50/60 |
50/60 |
50/60 |
No-load Voltage(V) |
67±5 |
65±5 |
65±5 |
65±5 |
65±5 |
68±5 |
Output current adjusting range(A) |
10-200 |
20-250 |
20-315 |
20-400 |
20-400 |
20-500 |
Duty cycle (%) |
60% |
60% |
60% |
60% |
60% |
60% |
Efficiency (%) |
85% |
85% |
85% |
85% |
85% |
85% |
Thrust adjustment (A) |
---- |
0-140 |
0-140 |
0-140 |
0-140 |
0-200 |
Power factor |
0.73 |
0.93 |
0.93 |
0.93 |
0.93 |
0.93 |
Insulation class |
F |
F |
F |
F |
F |
F |
Case protection degree |
IP21 |
IP21 |
IP21 |
IP21 |
IP21 |
IP21 |
Weight (kg) |
4.7 |
17 |
17 |
17 |
19 |
25 |
Overall dimension (cm) |
29x12x20 |
45x19x31 |
45x19x31 |
45x19x31 |
46x23x41 |
53x27x43 |
Base material |
Carbon steel ,low alloy steel , stainless steel |
|||||
Welding thickness (mm) |
1.5-5 |
1.5-10 |
1.5-10 |
1.5-12 |
1.5-12 |
1.5-12 |
Electrode diameter(mm) |
1.6-3.2 |
1.6-4.0 |
1.6-4.0 |
1.6-5.0 |
1.6-5.0 |
1.6-6.0 |
General Drawing or Sketch or Draft Drawing
Custom Electric Traveling Double Girder Overhead Cranes For Machine Shops
This is LH double Girder Electric Hoist Overhead Travelling Crane which use electric hoist as lifting mechanism. When heavy duty and wide span are required, the electric double beam electrical overhead travelling cranes for construction show their strength. They consist of two torsion-free box girders. This makes them especially suitable for lifting and transporting heavy loads.
Double Girder overhead industrial crane is characterized by strong bearing, big span, and overall stability with various models, but their quality is better compared with single girder gantry crane with the same capacity. They are available with load capacities up to 50T and with spans up to 35 m. Articulated end carriage joints ensure positive contact of all four wheels with the track. The range of fixing arrangements allows the appropriate integration of double girder travelling cranes into new buildings as well as into existing buildings. Just as with all other types of double girder travelling cranes, the profiles of the main girder are optimally produced using computers so that maximum performance with a minimum of dead-weight can be achieved. An advantage that has financial benefits.
Technical Parameters
Capacity |
Span |
Lifting Height |
Power |
Long travel Mechanism |
Cross Travel Mechanism |
|||||||
Pendent |
Cabin |
Hoist Type |
Lifting Speed |
Travelling Speed |
||||||||
Speed |
Motor |
Power |
Speed |
Motor |
Speed |
|
|
|
||||
t |
m |
|
m/min |
Model |
kW |
m/min |
Model |
kW |
|
m/min |
||
5 |
7.5 |
6;9;12; |
3P AC 380V50Hz |
28.72 |
YSE802- 4D |
2×0.8 |
42.9 |
YSE90L -4D |
2×1.5 |
CD1 (MD1)5- (6, 9, 12)- A2 |
8;8/0.8 |
17 |
10.5 |
||||||||||||
13.5 |
||||||||||||
16.5 |
||||||||||||
19.5 |
||||||||||||
22.5 |
||||||||||||
10 |
7.5 |
YSE90L-4D |
2×1.5 |
CD1 (MD1)10-(6, 9, 12)-A2 |
7;7/0.7 |
|||||||
10.5 |
||||||||||||
13.5 |
||||||||||||
16.5 |
||||||||||||
19.5 |
||||||||||||
22.5 |
||||||||||||
Rail Dia. |
Tread Width |
Max. Wheel Load |
Total Weight |
Dimension |
|
|||||||
K |
W |
L |
L1 |
H |
H1 |
H2 |
h |
|
||||
|
||||||||||||
mm |
KN |
t |
mm |
|
||||||||
Ф300 |
37-70 |
34.43 |
4.9 |
1500 |
3000 |
3550 |
120 |
1163 |
781 |
578 |
-3 |
|
38.04 |
5.86 |
17 |
|
|||||||||
40.9 |
6.78 |
107 |
|
|||||||||
44.13 |
7.98 |
187 |
|
|||||||||
47.17 |
9.2 |
267 |
|
|||||||||
50.28 |
10.7 |
347 |
|
|||||||||
57.28 |
5.6 |
121 |
1374 |
863 |
620 |
47 |
|
|||||
62.68 |
6.68 |
187 |
|
|||||||||
67.38 |
8.04 |
277 |
|
|||||||||
72.03 |
9.65 |
427 |
|
|||||||||
76.66 |
11.37 |
527 |
|
|||||||||
80.99 |
13.05 |
607 |
|
Double girder overhead crane with hoist are widely used in the following applications:
1. Light duty cranes for repair shops, light assembly operations, service buildings, light warehouses, where service requirements are infrequent.
2. Medium duty cranes for machine shops and general industrial use both indoor and outdoor application.
3. Extra heavy duty cranes for steel mills and other heavy machine shops, steel warehouses, heavy fabrication shops, paper mills etc. with magnet and bucket operation for scrap yards, fertilizer plants & induction furnace.
4. Extra heavy duty cranes for steel mills and other heavy engineering purposes. Cranes designed for hot metal application on request.
Design features include:
DESIGN:
Compact dimensions, low weight, easy to operate and easy to maintain, modular design with direct fits between components
Structure:
Bridge Girder, End carriages, Crab Frame manufactured from box plate design / Rolled Sections. If required 100% radiography of all butt welding joints of bridge and end carriages can be provided.
MOTORS:
NANTE Crane uses sturdy cylindrical/ conical rotor pole-changing motors with elegant continuous cast aluminum sections, integrated safety brakes insulation class F, IP54 protection.
Variable Frequency Drives & Remote Controls –
We also offer Variable Frequency Drive in hoisting, cross travel, long travel for stepless speed control as an optional feature. We also provide radio remote control cranes for application in inaccessible and hazardous areas.
Brakes –
Failsafe magnetic or hydraulic brakes of 150% torque or more are fitted on shaft extensions. For heavy duty cranes a second brake can be mounted to ensure failsafe operation.
Controls –
Pendant control from floor, master control switches, master controllers in the driver's cabin can be provided. Radio remote control can be provided on request.
ELECTRICAL PANEL:
Modular design, covering a very wide operating range. The systems are designed for ease of installation and maintenance and reliable operation, with fuseless circuitry, ducted wiring and non-screwed terminals. Each drive group is equipped with a motor overload protection device to provide effective protection against inadmissible overloading.
PAINTING:
Every component & part is thoroughly scrubbed & painted with two coats of primer before assembly & two coats of synthetic enamel after testing.
LIMIT SWITCHES:
To prevent over hoisting & over lowering of hook.
Electric Arc Welding Machine / Drawn Arc Stud Welder 3 - 13mm , High Frequency
RS-800 is a welding machine with German advanced electrical control technology. The main loop use non-inductance principles that reduce its dead weight on the basic of sufficient output power. Both welding current and time can be step-less adjusted. It is good equipment for welding insulation pin , boating manufacturing, pressure vessel, boiler and chemical welding and arc pin.
Technical Parameter
Drawn Arc Stud welder which could weld dia3-13mm studs . It suits to different material studs , such as copper plated , AL , Stainless Steel , Brass .
It sells well in General Industry , also with decoration industry.
Application:
Being in use of Car manufacturing , Train Stations , Industrial building , Household Adornment , high stress environment such as off road construction , large expansion bridges , skyscrapers , power plant , military defense vehicles , and equipment in high temperature environment .
Successful examples : Taizhou railway station , Direct Center of Baosteel Group shanghai No.5 Steel Co., ltd ., Beijing Olumpic Park National Meeting Center , Shanghai Television Station News Center , Canton Huilai Fire Power plant , Nanjing Olympic Center , Vehicle Testing Laboratory of China North Vehicle Research Institute .
Functions:
By welding Arc welding studs with material for copper plated, stainless steel and AL and Brass . Being in use of Car manufacturing , Train Stations , Industrial building , Household Adornment , high stress environment such as off road construction , large expansion bridges , skyscrapers , power plant , military defense vehicles , and equipment in high temperature environment .
Advantage:
1. Digital display of charging voltage and indication function of operating modes provide easy and visual operation .
2. Good welding quality and wide applicability .Available to various kinds of materials , such as carbon or stainless steel, aluminum and copper .Also suits to shear connector .
3. Now has been widely used in shipbuilding, boiler, transformer, automobile, building and bridge engineering, etc
4. Simiar functions of Germany Nelson stud welder
Power Supply:Standard 3-phase 220V/345V/380V/415V/440V 50/60Hz
Temporary rate :67/5% 20/60% 15/100%(KVA/%)
Work current (Max):800A
Welding time:50-1000ms
Stud Range:Φ3-Φ13 (mm)
Protection:Magnetic protection
Duty Cycle:32/Φ3 3/Φ13
Weight:138KG
Dimension:775mm×500mm×680mm
Induction Welding Machine 35KW With Six Control Thermocouples
Quick Detail:
Type:Other
Place of Origin:China (Mainland)
Brand Name:Canroon
Model Number:CR2000-035A-14T
Voltage:380V
Current:122A
Rated Capacity:35KW
Rated Duty Cycle:35KW
Dimensions:880*663*982
Weight:201Kg
Usage:induction temperature stress relievers
Certification:CE ISO9001:2008
After-sales Service Provided:Overseas service center available
Process:Induction heating equipment
Input Power:380V,3-Phase
Temperature recorder:6 Channel temperature recorder
Description:
Applications:
With the introduction of the Air cooled induction pipe heating machine , this simple and cost-effective heating process can be applied in the following applications to deliver fast and consistent heat:
Specifications:
Input Amperes at Rated Output |
380V:122A |
Thermal conversion efficiency |
More than 90% |
Maximum Rated output |
35KW |
Cooling Mode |
Air cooled |
Input Power |
380V 3-Phase,50HZ |
Rated Output |
35KW at 100% duty cycle,1-35KHZ |
TC input |
6 circuit |
Digital Recorder |
Optional |
Control Model |
Digital Control |
Resonance |
Series Resonance |
Temperature |
Max 1450°F |
Dimensions |
H:880MM W:663MM D:982MM |
Transportation |
By sea or By Air |
Weight |
201KG |
Warranty |
12 Months |
Competitive Advantage:
1.Versatile Mobility:optional running gear designed for construction and maintenance
2.On-board temperature control:provide for manual or temperature based programming in a simple-to-learn operator interface
3.Muitiple control thermocouple inputs:available to control on the hottest TC during heating and coolest TC during cooling for
4.uniform heating and quanlity
5.Open output detection:prevents system operation without a covered output receptacle(cable or protective plug)
6.Isolation fault protection:provides automatic system shut down power source output to ground.
7.Low consumable costs:No fuel costs and minimal insulation costs.insulation is resuable and may be used 50 time or more,reducing costs of disposal and replacement.
8.Uniform heating:maintained along and through the heat zone by using induction to heat within the material.the surface of the part is nor marred by localized conducted heat at higher than specified temperatutes.
9.Time-to-temperature:faster than conventional processes due to methed of applying the heat,reducing the heating heating recyle time.
10.Improved working environment: With welding,welders are not exposed to open flame,explosive gases and hot elements associated with fuel gas heating and resistance heating.
11.High energy-efficeent systems:(more than 90 percent efficient)transfers more energy to the part,decreassing heating times and impoving power efficietnt.
12.Easy Set-up:achieved using preheat blankets or flexible heating cables combined with user-friendly insulation blankets.
Tag: pipe heating machine
High Frequency Welding Machine copper-aluminium welding refrigerator cooling pipe welding
Using high frequency induction power supply output low voltage and high current, using on the solder points, Solder joint surface produce high-frequency electronic movement, forming eddy current, all the electrons move to generate heat (Skin effect and proximity effect),Make solder ontology surface temperatures to rise to the welding temperature,melting the welding ring and achieve the result of the solder joint sealing.
This equipment is main used for refrigerator, freezer,air-conditioner etc. Refrigeration appliance pipe welding.
2. The parameters of the equipment
1 |
Model |
TRHF-KV-Ⅲ |
2 |
Input pressure: |
Three phase 380V±10% 50/60HZ |
3 |
The maximum input power: |
11KVA |
4 |
The maximum output power |
10KVA |
5 |
Oscillation frequency |
21-27KHz |
6 |
Cooling Model |
water-cooling |
7 |
Water quality requirement |
distilled water |
8 |
Hydraulic pressure |
0.35~0.45 Mpa |
9 |
Flow |
10 ℓ/min |
10 |
Equipment environment requirements |
Temperature 5~40℃ humidity<85% |
Contact Person: Mr. zhang
Tel: 18810288990
Fax: 86-189-9086-7684